DIN 19569-2-2002 废水处理厂.构件和技术装备的设计原则.第2部分:固体分离和浓缩设备的特殊原则
作者:标准资料网 时间:2024-04-30 02:37:22 浏览:8729
来源:标准资料网
【英文标准名称】:Wastewatertreatmentplants-Principlesforthedesignofstructuresandtechnicalequipment-Part2:Specificprinciplesfortheequipmentforseparatingandthickeningofsolids
【原文标准名称】:废水处理厂.构件和技术装备的设计原则.第2部分:固体分离和浓缩设备的特殊原则
【标准号】:DIN19569-2-2002
【标准状态】:现行
【国别】:德国
【发布日期】:2002-12
【实施或试行日期】:
【发布单位】:德国标准化学会(DIN)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:安全工程;机械分离;污水处理工厂;寿命;集砂器;筛(污水);规范(验收);维修;设计;定义;建设工程;尺寸选定;污泥;分离;筛分设备;沉淀池;固体;建筑系统构件;污水处理;废弃物分离;负荷;排水工程;水常规;操作;过程测量和控制
【英文主题词】:
【摘要】:
【中国标准分类号】:Q81;P41
【国际标准分类号】:13_060_30
【页数】:28P;A4
【正文语种】:德语
Product Code:SAE CPGM2
Title:J1349 Certified Power Engine Data for GM L76 as used in 2007 Fullsize SUV's (Suburban, Yukon XL, Avalanche)
Issuing Committee:
Scope:This product includes information on the manufacturer, engine, applications, testing location, certified maximum horsepower, certified maximum torque along with the certified curves of horsepower and torque over a wide range of engine RPM speeds.In addition, this product contains complete engine information such as displacement, cylinder configuration, valve train, combustion cycle, pressure charging, charge air cooling, bore, stroke, cylinder numbering convention, firing order, compression ratio, fuel system, fuel system pressure, ignition system, knock control, intake manifold, exhaust manifold, cooling system, coolant liquid, thermostat, cooling fan, lubricating oil, fuel, fuel shut off speed, etc. Also included are all measured test parameters outlined in J2723.【英文标准名称】:Plasticspipingsystems-Polyethylene(PE)valves-Testmethodforresistancetobendingbetweensupports
【原文标准名称】:塑料管道系统.聚乙稀(PE)阀门.阀座间抗弯曲性的试验方法
【标准号】:BSEN12100-1998
【标准状态】:现行
【国别】:英国
【发布日期】:1998-02-15
【实施或试行日期】:1998-02-15
【发布单位】:英国标准学会(GB-BSI)
【起草单位】:BSI
【标准类型】:()
【标准水平】:()
【中文主题词】:弯曲试验;气体;方法;聚乙烯管道;管;管系统;塑料管道;塑料管;塑料;聚乙烯;电阻器;测试;三点荷载;阀门;管道阀门和配件
【英文主题词】:Bendtesting;Gases;Methods;PEpipes;Pipes;Pipingsystem;Plasticpipelines;Plasticpipes;Plastics;Polyethylene;Resistors;Testing;Three-pointloading;Valves;Valvesandfittingsforpipelines
【摘要】:Thisstandardspecifiesatestmethodfortheresistancetobendingofavalveinstalledbetweensupports.Thisstandardisapplicabletovalveswithapolyethylene(PE)bodyforusewithpipeshavinganominaloutsidediameterfromgreaterthan63mmuptoandincluding225mmandintendedforthetransportoffluids.
【中国标准分类号】:J16
【国际标准分类号】:23_040_01;23_060_01
【页数】:8P.;A4
【正文语种】:英语