MIL-PRF-5606H (AMENDMENT 3)
作者:标准资料网 时间:2024-05-04 20:41:52 浏览:8424
来源:标准资料网
MIL-PRF-5606H (AMENDMENT 3), PERFORMANCE SPECIFICATION HYDRAULIC FLUID, PETROLEUM BASE; AIRCRAFT, MISSILE, AND ORDNANCE (7 SEP 2006)., This specification describes the characteristics and provides the requirements for a petroleum base hydraulic fluid for use in the -54°C to +135°C temperature range (see 6.1). This fluid is identified by military symbol OHA and NATO Code No. H-515 (see 6.5).
基本信息
| 标准名称： | 硫化物矿物的电子探针定量分析方法 |
| 英文名称： | Quantitative analysis of sulfide minerals by electron probe microanalysis |
| 中标分类： |
仪器、仪表 >>
光学仪器 >>
电子光学与其他物理光学仪器 |
| ICS分类： |
成像技术 >>
光学设备
|
| 替代情况： | GB/T 15246-1994 |
| 发布部门： | 中华人民共和国国家质量监督检验检疫总局 |
| 发布日期： | 2002-11-11 |
| 实施日期： | 2003-06-01 |
| 首发日期： | 1994-10-17 |
| 作废日期： | 1900-01-01 |
| 主管部门： | 国家标准化管理委员会 |
| 提出单位： | 全国微束分析标准化技术委员会 |
| 归口单位： | 全国微束分析标准化技术委员会 |
| 起草单位： | 中国地质科学院成都矿产综合利用研究所 |
| 起草人： | 毛水和 |
| 出版社： | 中国标准出版社 |
| 出版日期： | 2003-06-01 |
| 页数： | 平装16开， 页数：8， 字数：12千字 |
| 书号： | 155066.1-19238 |
适用范围
本标准规定了用电子探针进行硫化物定量分析的标准方法。本标准适用于在电子束轰击下稳定的硫化物以及砷化物、锑化物、铋化物、碲化物、硒化物的电子探针定量分析。本标准适用于以X射线波长分光谱仪进行的定量分析；其主要内容和基本原则也适用于以X射线能谱仪进行的定量分析。
前言
没有内容
目录
没有内容
引用标准
没有内容
所属分类： 仪器 仪表 光学仪器 电子光学与其他物理光学仪器 成像技术 光学设备
Product Code:SAE J1832
Title:Low Pressure Gasoline Fuel Injector
Issuing Committee:Gasoline Fuel Injection Standards Committee
Scope:This SAE Recommended Practice promotes uniformity in the evaluation and qualification tests conducted on fuel injectors used in gasoline engine applications. Its scope is limited to electronically actuated fuel injection devices used in automotive port or throttle body fuel injection systems where fuel supply pressure is below 1000 kPa. It is primarily restricted to bench tests. More specifically, this document is intended for use as a guide to the following:Standardize use of nomenclature specifically related to fuel injectors.Identify and define those parameters that are used to measure fuel injector characteristics or performance. The parameters included in this document are listed along with their recommended symbol where appropriate:Closing Time (CT)Inductance (L)Coil Resistance (R)Dynamic Flow (Qd)Dynamic Flow Calculated (Qdc)Dynamic Flow Rate (Q)Dynamic Flow Temperature Shift (Qtd)Dynamic Flow Vacuum Shift (Qvd)Dynamic Minimum Operating Voltage (DMOV)Dynamic Set Point (PWxx)Dynamic Set Point Flow (Qsp)External LeakageFlow-Offset (Y)Insulation Resistance (IR)Linear Flow Range (LFR)Linearity Deviation (LD)Maximum Overload VoltageOpening Time (OT)Operating Voltage RangePeriod (P)Pulse Width (PW)Pressure Drop Ratio (PDR)RepeatabilitySlope (m)Slope Approximated (ma)Spray PatternStability (S)Static Drop-Out Current (I/S-OFF)Static Flow Rate (Qs)Static Minimum Operating Voltage (SMOV)Static Pull-In Current (I/S-ON)Time-Offset (X)Working Flow Range (WFR)Establish test procedures and recommend test equipment and methods to measure and quantify these parameters.Establish test procedures, and recommend test equipment and methods to quantify simulated field reliability over the life of the component.Except where stated, test results are recorded for individual parts under recommended test conditions. Where population characteristics are reported, the sample size, selection method, and analysis technique must be explicitly stated.Any testing practices which are different than those recommended in this specification should be noted on the data collection sheet.
